CTR24L - 2515

KEY FEATURES

  • High brightness display : 6-digit LED, height 8 mm
  • Maximum input frequency 50 k Hz (in tot.tot function)
  • Programmable dual functions : Counter + Tachometer/Counter + Counter/Counter + Chronometer/Chronometer + Chronometer
  • Reset on panel or external with inhibition option
  • Supply : 10 →30 V\⎓
  • Easy to program
  • Scaling factor (Counter - Tachometer)
  • Decimal point (Counter - Tachometer - Chronometer)
  • Timing range 0.001 s →999,999 hrs (Chronometer)
  • Impulses or time measured in hrs/min/sec and in real time (Chronometer)
  • Accessories for 50 x 25 mm cut-out
FunctionsCode
DUO counter : Counter + Tachometer/Counter + Counter/Counter + Chronometer/Chronometer + Chronometer87623574

Specifications


Consumption 10 →30 V⎓ max 55 mA with protection against polarity reversal
Connection by 5 screw terminals at rear of casing
Connection capacity 1,5 mm2
Fixed using bracket
Degree of protection front face IP 65
Data memory EEPROM
Temperature limits use (°C) -20 →+55
Temperature limits stored (°C) -25 →+70
Breakdown voltage EN 61010-1 : 2000 V / 50 Hz / 1 min
Conformity to standards EN 61000-6-2 - EN 55011 class B
Altitude 2000 m
Certifications UL - cULus (pending) - CE
Weight (g) 50

Functions Counter + Tachometer/Counter + Counter/Counter + Chronometer/Chronometer + Chronometer
Display 6-digit LED
Height digits (mm) 8

Inputs 2 counter inputs, 1 reset input
Low level 0 →0,2 x Ub V⎓
High level 0,6 x Ub →30 V⎓
Cyclical ratio Any (maximum frequency given for a cyclical ratio = 1/1) Schmitt trigger input
Polarity NPN or PNP for all inputs (programming)
Minimum impulse duration for reset 5 ms
Frequency of filtered input Filter active : 30 Hz Filter disabled : maximum frequency (programming)
Input impedance (kΩ) Appr. 5

Display details 0 →999 999
Elimination of non-significant zeros
Counting input modes INPA input counting
Input INPA Dynamic (uses the same INPA input as the counter)
Reset input (terminal 5) Dynamic Reset input connected in parallel with the red SET/RESET button Sets the counter to the defined preset value
Reset to zero - Panel If not locked during programming
Remise à zéro - Externe (borne 5) If not locked during programming
Scale factor 1 →99,9999
Scaling factor 1 →99,9999
Decimal point 0 0,0 0,00 0,000
Maximum counting frequency 50 k Hz

Display details 0 →999 999
Elimination of non-significant zeros
Conversion time 1/s or 1/min
Input INPA Dynamic (uses the same INPA input as the counter)
Accuracy < 38 Hz : measurement of period duration > 38 Hz : measurement of duration time base = 26.3 ms
Measurement principle < 0.1 %
Scale factor 1 →99,9999
Scaling factor 1 →99,9999
Decimal point 0 0,0 0,00 0,000
Maximum counting frequency 35 k Hz

Display details 0,001 s →999 999 h
Elimination of non-significant zeros
Functions In tot.tr function : GatE.Lo →Time measurement if INPB is not active GatE.hi →Time measurement if INPB is active Inb.Inb →Time measurement on/off via the INPB edge In tr.tr function : IGatE.Lo →Time measurement if INPB is not active GatE.hi →Time measurement if INPB is active Inb.Inb →Time measurement on/off via the INPB edge InA.Inb →Measurement on via the INPA edge, measurement off via the INPB edge
Input INPA Start/Stop or Gate (depends on the input mode chosen)
Input INPB Start/Stop or Gate (depends on the input mode chosen)
Reset input (terminal 5) Dynamic Reset input connected in parallel with the red SET/RESET button Sets the counter to the defined preset value
Remise à zéro - Externe (borne 5) If not locked during programming
Reset to zero - Panel If not locked during programming
Accuracy < 50
Decimal point 0 0,0 0,00 0,000
Time ranges 0,001 s →999 999 s 0,001 min →99 999 min 0,001 h →999 999 h 00 h 00 min 01 s →99 h 59 min 59 s
Maximum counting frequency 40 k Hz

Technical sketches

CTR24L - 2515

CTR24L - 2515

Fixing strip with clip-on yoke

Fixing strip with clip-on yoke
Legend
1-
Seal
2-
Fixing yoke

Panel cut-out

Panel cut-out

4 appliances

4 appliances

26546843 - Adaptor for 50 x 25 mm cut-out - Fixed with screws

26546843 - Adaptor for 50 x 25 mm cut-out - Fixed with screws

26546844 - Adaptor for 50 x 25 mm cut-out - Fixed with clips

26546844 - Adaptor for 50 x 25 mm cut-out - Fixed with clips
Accessory supplied with the counter

26546840 - DIN rail adaptor

26546840 - DIN rail adaptor
Legend
1-
Supply : 10 →30 V⎓
2-
Supply : GND (0 V⎓)
3-
INPA
4-
INPB
5-
SET/RESET
PH 87621112

Programming diagram

Programming diagram

Share
Share
luctus felis leo suscipit venenatis sit Phasellus